Blog > Blogs

Activated Carbon in Effluent Treatment Plants: Tertiary Polishing for COD, Colour and Odour Removal

image
AI Icon Summarize this Article with AI

Key Highlights

  • Activated carbon tertiary polishing removes 60-85% of residual COD after biological treatment in ETPs
  • GAC fixed-bed filters and PAC dosing are the two principal application methods, each suited to different plant configurations
  • Colour removal from textile, dye and food processing effluent is one of the most demanding ETP applications for activated carbon
  • CPCB General Standards under the Environment Protection Act set discharge limits that tertiary carbon polishing helps industries meet
  • PAC dosing rates for industrial ETP range from 50 to 300 mg/L depending on contaminant load and target outlet quality
  • Western Carbon supplies GAC and PAC grades optimised for Indian industrial ETP requirements across textile, pharmaceutical, food and chemical sectors

Effluent treatment plants across Indian industry face a consistent challenge: biological and chemical treatment stages reduce BOD and suspended solids effectively, but they leave behind a residual load of dissolved organics, colourants, trace pharmaceuticals and odour compounds that standard secondary treatment cannot fully address. Meeting CPCB discharge standards for inland water bodies, particularly for COD, colour and odour, requires a polishing stage that targets these persistent contaminants specifically.

Activated carbon tertiary polishing has become the preferred solution for industries ranging from textiles and pharmaceuticals to food processing and chemicals. Using granular activated carbon in fixed-bed filters or powdered activated carbon dosed into clarifiers, plant operators can achieve the final effluent quality needed for regulatory compliance and, in zero-liquid-discharge schemes, for water reuse. This guide covers the science, the selection criteria and the practical operating parameters for activated carbon in ETP tertiary polishing.

1. What Is Tertiary Treatment in an Effluent Treatment Plant?

An ETP typically operates in three sequential stages. Primary treatment uses screens, grit chambers and primary clarifiers to remove settleable solids and floating matter. Secondary treatment employs biological processes, most commonly activated sludge, moving bed biofilm reactors or sequencing batch reactors, to biodegrade dissolved BOD and suspended organics. The effluent leaving secondary treatment still carries residual dissolved organics measured as COD, colour from dyes and pigments, odour from sulphur compounds and trace contaminants that resist biological breakdown.

Tertiary treatment addresses these residuals. It encompasses a range of physical, chemical and biological unit processes applied after secondary clarification. Common tertiary processes include sand filtration, membrane filtration, UV disinfection, ozonation and activated carbon adsorption. In practice, most industrial ETPs that need to meet stringent COD or colour limits use activated carbon as their primary tertiary polishing technology, often combined with upstream sand filtration to reduce the suspended solids load entering the carbon beds.

What Tertiary Treatment Must Achieve

The CPCB General Standards for Discharge into Inland Surface Water under Schedule VI of the Environment Protection Rules 1986 set a COD limit of 250 mg/L and a BOD limit of 30 mg/L. Many state pollution control boards apply stricter limits. Colour has no universal numeric limit under the General Standards but is listed as a parameter that must be absent or negligible. Odour is similarly a qualitative discharge requirement. Activated carbon tertiary polishing is particularly well matched to these parameters because adsorption targets dissolved organics and colourants selectively, independent of biodegradability.

!

Tertiary polishing with activated carbon is not a substitute for properly functioning primary and secondary treatment. Carbon beds achieve best performance when the feed COD from secondary treatment is below 300 mg/L and suspended solids are below 50 mg/L. High solids loading accelerates carbon exhaustion and reduces bed life.

2. Why Activated Carbon Is Used for ETP Polishing

Activated carbon is a highly porous form of carbon produced by carbonisation and activation of coconut shell, coal or wood precursors. The activation process, using steam or chemical agents, develops an extensive internal pore network with surface areas typically between 800 and 1200 m2/g. This pore structure creates the adsorption capacity that makes activated carbon effective for removing dissolved contaminants from water and wastewater.

In ETP applications, the adsorption mechanism captures dissolved organic molecules through van der Waals forces and electrostatic interactions at the carbon surface. Contaminants with larger molecular weight, hydrophobic character and aromatic ring structures adsorb most strongly. This includes reactive dyes, disperse dyes, pharmaceutical compounds, chlorinated solvents, phenols and many industrial by-products that resist biological treatment.

Advantages Over Alternative Tertiary Processes

Ozonation and advanced oxidation processes can break down refractory organics but require significant capital investment and produce oxidation by-products that must be managed. Membrane systems achieve excellent separation but foul rapidly with coloured or high-COD effluent and generate a concentrated reject stream. Activated carbon offers a comparatively simpler technology with no chemical additions beyond the carbon itself, no high-pressure operation and an established supply chain for carbon media.

The adsorption process is reversible in principle, which means exhausted GAC can be thermally regenerated and reused, reducing long-term operating costs in large installations. PAC, while not economically regenerable, offers flexibility for variable loading and can be added to existing clarifier infrastructure without building dedicated filter vessels.

3. COD Reduction Using Activated Carbon in ETP

COD (Chemical Oxygen Demand) measures the total oxygen equivalent of oxidisable substances in water. After secondary biological treatment, residual COD consists primarily of non-biodegradable dissolved organics, colloidal material that escaped clarification and slowly biodegradable compounds. This refractory COD fraction is precisely the type of contamination that activated carbon adsorption addresses most effectively.

Studies published in environmental engineering literature consistently show 60 to 85% COD reduction across GAC tertiary filters when feed COD is in the 100 to 400 mg/L range. The specific reduction depends on the nature of the organic contamination: low molecular weight aliphatic compounds adsorb less strongly than aromatic or high molecular weight organics, so an effluent dominated by simple organic acids will show lower COD removal than one containing dye compounds or pharmaceutical residues.

Key fact: A GAC tertiary filter with an empty bed contact time of 15 to 30 minutes typically reduces effluent COD from 150-250 mg/L (secondary treatment outlet) to 30-80 mg/L, well within CPCB inland surface water discharge limits.

COD Range (Secondary Outlet, mg/L) Expected GAC Removal (%) Typical Outlet COD (mg/L) CPCB Limit Met?
100 – 200 70 – 85% 15 – 60 Yes
200 – 350 60 – 75% 50 – 140 Mostly
350 – 500 50 – 65% 120 – 250 Borderline
Above 500 40 – 55% 225 – 300+ Unlikely without pre-treatment

For high COD feeds, staged carbon filtration with two beds in series improves performance. The first bed handles the bulk of adsorption; the second bed provides polishing. When the first bed reaches breakthrough, it is taken offline for regeneration or replacement and the second bed moves to the lead position, with a fresh bed placed in the lag position. This lead-lag configuration is standard practice in well-engineered ETP carbon systems.

4. Colour Removal from Industrial Effluent with Activated Carbon

Colour is one of the most visible indicators of industrial effluent quality and one of the most difficult parameters to treat by conventional means. Textile dyeing, dye manufacturing, food processing, leather tanning and pharmaceutical fermentation all generate coloured effluents. Many synthetic dyes, particularly reactive, disperse and vat dyes used in textiles, are highly stable aromatic compounds designed to resist degradation during use. This stability makes them equally resistant to biological treatment in ETPs.

Activated carbon adsorbs dye molecules effectively because dyes are typically large, aromatic, hydrophobic compounds with high affinity for the carbon surface. Activated carbon performance for colour removal depends on dye molecular weight, ionic character (anionic dyes generally adsorb less strongly than cationic dyes on carbon at neutral pH), and the carbon grade’s pore size distribution. Dyes with large molecular weights require mesopore access, so carbons with broader pore size distributions perform better for textile effluent than carbons with predominantly microporous structure.

Colour Removal Efficiency by Application

Application Sector Primary Colourants PAC Dose for 80% Colour Removal GAC EBCT Required
Textile (reactive dyes) Reactive, disperse, acid dyes 150 – 250 mg/L 20 – 30 min
Food and beverage Caramel, anthocyanins, synthetic food colours 50 – 100 mg/L 10 – 20 min
Paper and pulp Lignin derivatives, chlorophenols 100 – 200 mg/L 15 – 25 min
Pharmaceutical Fermentation pigments, APIs 80 – 150 mg/L 15 – 20 min
Dye manufacturing Intermediates, azo dyes 200 – 300 mg/L 25 – 40 min

For textile ETPs targeting zero liquid discharge (ZLD) with effluent reuse in process water, colour must be reduced to near zero. This requires higher carbon doses or longer contact times than standard discharge scenarios, and the activated carbon selection should favour grades with high iodine number and broad pore size distribution to handle the range of dye molecular sizes present in a typical mixed-dye effluent.

!

Colour removal by activated carbon is pH-dependent. Many reactive dyes used in cotton dyeing adsorb more strongly at lower pH. Where plant design allows, treating the carbon stage at pH 5 to 6 before final pH correction can improve colour removal efficiency by 15 to 25%.

5. Odour Control in Effluent Treatment Using Activated Carbon

Odour complaints are among the most common regulatory and community issues faced by industrial ETPs located near residential areas. ETP odour originates from multiple sources: hydrogen sulphide generated by anaerobic zones in collection sumps and primary clarifiers, reduced sulphur compounds from biological treatment, ammonia from nitrogenous waste, and volatile organic compounds (VOCs) from industrial process effluents. These compounds reach concentrations detectable by the human nose at parts-per-billion levels, making odour one of the most sensitive parameters to control.

Activated carbon addresses odour through two mechanisms. For dissolved odour compounds in the liquid phase, adsorption in the carbon filter removes them before effluent is discharged. For air-phase odour control at ETP structures, activated carbon is used in packed bed scrubbers treating exhaust air from enclosed sumps, biological reactors and sludge handling areas. Westdiox impregnated carbon grades offer enhanced removal of hydrogen sulphide and other sulphur-based odourants in gas-phase applications.

Activated Carbon Supply for Your ETP

Western Carbon supplies GAC and PAC grades optimised for tertiary ETP treatment. We help you select the right grade for your COD, colour and odour targets.

Get ETP Carbon Recommendations

Odour Compounds Removed by Activated Carbon in ETP

Odour Compound Source in ETP Activated Carbon Effectiveness Recommended Carbon Type
Hydrogen sulphide (H2S) Anaerobic zones, sludge High (gas phase) Impregnated GAC
Mercaptans Chemical and food industry effluent High Standard or impregnated GAC
Ammonia Nitrogen-rich effluent Moderate (liquid phase) Acid-washed GAC
Phenol and cresols Chemical industry effluent High (liquid phase) High iodine number GAC
Dimethyl sulphide Fermentation, paper effluent High (gas phase) Standard GAC

6. GAC vs PAC in ETP: Which to Choose for Your Application

The choice between granular activated carbon (GAC) and powdered activated carbon (PAC) is one of the most consequential decisions in ETP carbon system design. Both forms adsorb the same contaminants by the same mechanism, but they differ substantially in how they are applied, their capital and operating cost profiles, and their suitability for different plant configurations.

GAC is used in fixed-bed pressure or gravity filters, with the carbon retained in the vessel while water flows through. This allows continuous operation with an extended bed life and the possibility of thermal regeneration when the carbon is exhausted. GAC systems require dedicated filter vessels, backwash infrastructure and, for regeneration, offsite thermal treatment or on-site regeneration furnaces. The capital cost is higher, but the ability to regenerate carbon and the low media consumption per unit of water treated make GAC more economical over long operating periods.

PAC is added directly to the ETP process stream, typically into a contact tank before clarification or into the aeration basin of a biological treatment stage. PAC mixes with the effluent, adsorbs contaminants during a contact period, and is then separated with the settled sludge in the clarifier. PAC cannot be regenerated economically, so it is consumed as a reagent. Capital cost is minimal, as no dedicated filter infrastructure is needed, making PAC well suited to retrofitting existing ETPs and handling seasonal or shock loading scenarios.

Parameter GAC Fixed Bed PAC Dosing
Capital cost High (filter vessels, backwash system) Low (dosing tank and pump)
Operating cost Lower long-term (regenerable) Higher long-term (consumable)
Flexibility Fixed capacity, designed for steady loads High: dose can be adjusted to load
Retrofit ease Requires dedicated infrastructure Easy to add to existing clarifiers
Sludge generation Minimal (backwash solids only) Significant (PAC-laden sludge)
Best suited for High-volume, steady-state ETP with consistent COD Batch processes, seasonal loading, shock events

For large industrial ETPs treating more than 500 m3/day on a continuous basis, GAC fixed-bed systems with regeneration typically offer the lowest lifecycle cost. For smaller ETPs, batch operations or plants with highly variable influent, PAC dosing often provides better value. Some plants use a combined approach: GAC for base-load polishing with PAC as a supplementary dose during high-load periods or batch treatment of off-spec effluent.

7. Carbon Dosing Rates and Contact Time for ETP Applications

Accurate carbon dosing is critical to both regulatory compliance and cost management. Under-dosing results in inadequate COD or colour removal and regulatory failure. Over-dosing increases operating costs without proportional improvement in effluent quality, since adsorption capacity follows a diminishing-returns relationship described by the Freundlich or Langmuir isotherm equations.

PAC Dosing Rates by Industry

Industry Sector Typical PAC Dose (mg/L) Target Parameter Contact Time Required
Textile (dyeing and finishing) 150 – 300 Colour and COD 30 – 60 min
Pharmaceutical manufacturing 80 – 200 COD and APIs 20 – 45 min
Food and beverage processing 50 – 100 COD and colour 15 – 30 min
Chemical manufacturing 100 – 250 COD and phenolics 30 – 60 min
Leather tanning 100 – 200 Colour and COD 20 – 40 min
Paper and pulp 120 – 250 COD and lignin 25 – 50 min

GAC Filter Design Parameters

GAC filter design is governed by the empty bed contact time (EBCT), which is the theoretical time the effluent spends in contact with the carbon bed. EBCT is calculated as the carbon bed volume divided by the volumetric flow rate. For ETP tertiary polishing, EBCT values of 10 to 30 minutes are typical, with longer contact times required for more complex organic mixtures or higher COD loads.

Surface loading rates for GAC filters in ETP service typically range from 5 to 15 m/h. Higher rates reduce contact time and may cause channelling in the bed. Backwash frequency depends on influent suspended solids but is typically once every 24 to 72 hours for well-pretreated ETP effluent. Granular activated carbon filter systems are sized with these parameters to ensure consistent performance throughout the bed life.

!

Jar testing using actual plant effluent samples is the most reliable method for establishing PAC dosing requirements. Laboratory isotherm tests using the Freundlich model can predict equilibrium capacity, but actual plant conditions including temperature, pH variations and competing adsorbates affect real-world performance. Always validate laboratory results with a pilot test before full-scale design.

8. Regeneration and Replacement of Activated Carbon in ETPs

Activated carbon does not degrade chemically during the adsorption process; it reaches saturation when all available adsorption sites are occupied by contaminants. At this point, the carbon must either be replaced with fresh media or regenerated to restore adsorption capacity.

When to Replace or Regenerate GAC

The standard indicator of GAC exhaustion is breakthrough: the point at which the effluent COD or colour at the bed outlet begins to rise toward feed concentrations. For regulatory compliance, breakthrough must be caught before the outlet quality fails permit limits. Well-designed systems monitor outlet quality continuously and have a planned protocol for carbon change-out or regeneration before breakthrough reaches the permit limit.

In practice, GAC bed life in ETP applications depends heavily on contaminant loading. Lightly loaded beds treating low-COD municipal-quality secondary effluent may operate for two to five years before exhaustion. Heavily loaded industrial ETP beds treating textile or pharmaceutical effluent often require change-out every six to eighteen months. Tracking the cumulative mass of contaminants removed per kilogram of carbon (the specific throughput) is the most accurate way to predict remaining bed life.

Thermal Regeneration

Spent GAC can be thermally regenerated by heating to 800 to 1000 degrees Celsius in a controlled atmosphere, burning off adsorbed organics and restoring the pore structure. Each regeneration cycle results in approximately 5 to 10% carbon loss from attrition and burnout, so regenerated carbon is topped up with virgin makeup carbon. Thermal regeneration is economically viable only for large installations where the carbon volume justifies the logistics and processing cost. Western Carbon provides guidance on regeneration thresholds and can supply replacement granular activated carbon for ETP systems requiring media change-out.

9. Industries That Use Activated Carbon in ETP: Textile, Pharma, Food Processing

Activated carbon tertiary polishing is applicable across a wide range of industrial sectors, each with its characteristic effluent composition and treatment challenge.

Textile Industry ETPs

Textile dyeing and finishing is the largest single application for activated carbon in Indian industrial ETP. Processing cotton, polyester and blended fabrics requires large volumes of water and generates effluent containing reactive dyes, disperse dyes, surfactants, sizing agents and salts. Colour is the defining treatment challenge, and activated carbon is the most effective technology for final colour polishing. Many textile ETPs in Gujarat, Maharashtra and Tamil Nadu use GAC filters as the final stage before effluent reuse or discharge. Westfiltra grades are formulated specifically for textile and dye effluent applications.

Pharmaceutical Manufacturing ETPs

Pharmaceutical ETPs treat complex effluent streams containing active pharmaceutical ingredients, solvents, fermentation broth residues and synthetic organic compounds. Many of these compounds are refractory to biological treatment and are present at concentrations that may be toxic to biological treatment organisms if not managed carefully. GAC tertiary polishing removes API residues, reduces COD from non-biodegradable organics, and helps pharmaceutical manufacturers meet both CPCB and international effluent standards. Acid-washed activated carbon is often specified for pharmaceutical ETP applications where low ash content and high purity are required. The Westpharm range is designed for pharmaceutical sector applications.

Food and Beverage Processing ETPs

Food and beverage processing generates effluent with high BOD and COD from sugars, proteins and fats, along with colour from caramelisation products, natural pigments and processing additives. While biological treatment handles most of the BOD load effectively, the final colour and COD residual benefits from activated carbon polishing. Westoilpure grades are used in edible oil and food processing ETP applications. PAC dosing is frequently used in food industry ETPs due to the variable nature of production schedules and batch processing.

Chemical and Petrochemical ETPs

Chemical manufacturing ETPs handle phenols, chlorinated organics, aromatic solvents and industrial by-products that are poorly biodegradable. GAC tertiary polishing is essential for these applications, often using extruded activated carbon pellets in fixed-bed reactors where pressure drop management is critical in high-flow systems.

10. Western Carbon Serves Customers Worldwide

Western Carbon & Chemicals supplies activated carbon for ETP tertiary polishing to industrial customers across India and in export markets globally. Our technical team provides grade selection guidance, dosing calculations and ongoing support for ETP carbon systems.

Improve Your ETP Effluent Quality with Activated Carbon

Western Carbon supplies granular and powdered activated carbon for industrial effluent treatment across India and globally. Meet CPCB discharge standards with the right carbon grade.

Talk to Our Technical Team

Or explore PAC for wastewater treatment

12. Frequently Asked Questions

What is the role of activated carbon in an ETP?

Activated carbon is used in the tertiary stage of an ETP to adsorb dissolved organics, colourants, trace contaminants and odour-causing compounds that biological and chemical treatment stages cannot fully remove. It acts as a polishing step to meet CPCB and state board discharge standards. For product options, see our range of activated carbon products.

What COD reduction can I expect from activated carbon in an ETP?

Activated carbon tertiary filters typically achieve 60-85% additional COD reduction after secondary treatment. The final achievable COD depends on influent quality, carbon grade, empty bed contact time, and the nature of organic contaminants. A properly designed GAC filter can routinely deliver outlet COD below 80 mg/L when feed COD from secondary treatment is 200-300 mg/L.

Should I use GAC or PAC in my effluent treatment plant?

GAC is preferred for continuous fixed-bed filtration with regeneration potential, making it cost-effective for high-volume ETPs. PAC is better for batch or seasonal dosing, handling shock loads, and retrofitting existing clarifiers without building a separate filter unit. Many large ETPs use both: GAC for base-load polishing and PAC for peak loading. Contact our team to discuss which approach suits your plant design.

What is the typical PAC dosing rate for ETP colour removal?

PAC dosing for colour removal in ETPs typically ranges from 50 to 300 mg/L depending on the initial colour load and target outlet quality. Textile effluent with reactive dyes often requires 150-250 mg/L for effective decolourisation. Food and beverage effluent is typically treated at 50-100 mg/L. Jar testing with plant effluent samples gives the most accurate dosing requirement for your specific wastewater.

How often does GAC need to be replaced in an ETP filter?

GAC bed life in ETP applications depends on contaminant loading. In industrial ETPs treating textile or pharma effluent, GAC beds typically require replacement or thermal regeneration every 6 to 24 months. Tracking outlet COD or colour breakthrough is the most reliable indicator. Western Carbon can help you calculate expected bed life based on your effluent characterisation data.

Can activated carbon handle heavy metals in ETP effluent?

Standard activated carbon has limited capacity for heavy metal removal. Acid-washed activated carbon offers better performance for certain metals, and impregnated grades are used for specific metal applications. For primary heavy metal removal, chemical precipitation is recommended before the carbon polishing stage. Activated carbon then handles the organic and colour load in the tertiary stage.

What CPCB standards does activated carbon help meet in ETP discharge?

Activated carbon tertiary polishing helps ETPs meet CPCB General Standards under Schedule VI of the Environment Protection Rules 1986 for parameters including BOD (less than 30 mg/L), COD (less than 250 mg/L for inland surface water), colour, and odour. Many state pollution control boards apply stricter limits. See our quality certifications page for details on the carbon grades we supply for compliance applications.

Is activated carbon effective for pharmaceutical ETP effluent?

Yes. Pharmaceutical ETPs use GAC tertiary polishing extensively to remove active pharmaceutical ingredients (APIs), solvents, and persistent organic pollutants that survive biological treatment. High iodine number GAC grades with micropore development are preferred for pharma applications. Our Westpharm range is specifically formulated for pharmaceutical sector ETP requirements, including low ash content and high adsorption capacity for pharmaceutical compounds.

External references: (1) CPCB General Standards for Discharge, Environment Protection Rules 1986, Schedule VI; (2) Metcalf and Eddy, Wastewater Engineering: Treatment and Resource Recovery, 5th Edition, McGraw-Hill, 2014; (3) Crittenden, J.C. et al., MWH’s Water Treatment: Principles and Design, 3rd Edition, Wiley, 2012; (4) Foo, K.Y. and Hameed, B.H., “Insights into the Modelling of Adsorption Isotherm Systems,” Chemical Engineering Journal, Vol. 156, Issue 1, 2010; (5) Central Pollution Control Board, Comprehensive Industry Document for Textile Sector, COINDS/70/2009-10, New Delhi.